Manual programming tyt th 9000 serial#

According to the pinout diagram provided by the SLVRC, this meant that the pin closest to the back of the radio was #6, therefore pin numbering ran 1 through 6 from the front to the back of the radio. By plugging the new cable into the socket and checking with my digital volt meter, I was able to figure it out by checking for five volts. After getting the first TYT- TH9000 open (a bit of a challenge due to the use of small Torx head screws), I notice that the six pin socket was not labeled. Matt gave me his TYT- TH9000 and Todd ordered the newer TYT-TH9000D (see his article).Д¤ Using the Digi-Key part number (A100196-ND) from the SLVRC posting, I ordered the cables and DE-9 connectors from Digi-Key, which arrived a few days later: It was now time to take a look under the hood. To my delight, Todd (KD0 TLS) and Matt (N0 YNT) came forward with the offer of two radios. With this information in hand, I put out a request that I would Build the repeater, if someone donated the radios.

Manual programming tyt th 9000 serial#

Build a repeater from TYT- TH9000 Mobile Transceivers Dan went on to state The TYT TH9000 has a plastic cover hiding a machined opening to fit a 9 pin serial port, complete with 2 threaded holes to mount a serial port. Build a repeater from TYT- TH9000 Mobile Transceivers of 7. Dan (VA3OT) provided information about the TYT- TH9000, what he found was that all the necessary connections needed to make a functioning repeater was present on a 6-Pin board mounted socket: of 7. But what caught my eye was at the bottom of the page. They reflected on what we already know, that the 220 Amateur radio band is being poached (they too lost 220 to 222 MHz to commercial interests) and warned, Use it or lose it!ДЈ The shortage of equipment is discussed and they provide a list of what is available, including the previously referenced Hamtronics boards. The Saint Lawrence Valley repeater Council (SLVRC) or Comit de Coordination de Fr quences de la Vall e du St-Laurent enlightened me when I clicked their Notes on the 222 MHz Band link. Internet research leads me to a web site hosted by our neighbors to the north. Trying to keep an open mind, I realized that most of what we purchase in the way of electronics (including amateur gear) is probably manufactured in China anyhow, so I investigated further.

He suggested that we consider building a 220 repeater from two TYT- TH9000 Mobile transceivers! Oh I had to overcome the perception that these were cheap Chinese radios and the concept would not be feasible due to technical or quality issues. Дў While pondering this dilemma, an innovative idea was suggested by KD0 TLS (Todd). The two boards alone would cost $ and would only be a starting point for a repeater. who sell VHF FM exciter and receiver boards. The story is very different today with the only choice available being Hamtronics, Inc. Back in the day you could obtain boards, modules or entire 220 band repeaters from companies such as SCC and VHF Engineering. When it was working, this repeater was probably the best performing 220 repeater in the Twin Cities area due to its excellent location and 80 watts of RF power. This repeater had served the club and the ham radio community for many years and was built from Spectrum Communications Corporation (SCC) modules mounted in a VHF Engineering enclosure. It all started when the Twin Cities repeater Club's aging 220 repeater on MHz failed due to what appeared to be audio problems. Д«uild a repeater from TYT- TH9000 Mobile Transceivers Now it was a simple matter to peel off the sticker covering the 9-pin serial port cut-out andДЎ Build a repeater from TYT- TH9000 Mobile Transceivers Part 1 Modifying the TYT- TH9000 (D).

Example: stock market Search Build a repeater from TYT- TH9000 Mobile вЂ¦Д«uild a repeater from TYT- TH9000 Mobile Transceivers Part 1 Modifying the TYT- TH9000 (D).

Manual programming tyt th-9000